QW-462.10(c) Shear Strength Requirements for Spot or Projection Weld Specimens
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (6.79 MB, 434 trang )
Figure QW-462.12
Nomenclature for Temper Bead Welding
S [Note (1)]
Approx. 0.040 in. (1 mm)
Also showing location of
hardness traverses when
hardness testing is used.
Partially Completed Partial-Penetration Weld
Approx. 0.040 in. (1 mm)
Typical Groove Weld
Approx. 0.040 in. (1 mm)
S [Note (1)]
S [Note (1)])
ASME BPVC.IX-2015
206
Also showing location of hardness traverses when hardness testing is used.
Completed Partial-Penetration Weld
Weld Beads Against Base Metal
First Layer Tempering Beads
LEGEND
See Note (2)
Typical Fillet Weld
Approx.
0.040 in. (1 mm)
S [Note (1)]
Second Layer Tempering Beads
Approx.
0.040 in.
(1 mm)
Fill Weld Beads
Also showing permissible locations and orientations of hardness traverses.
Overlay Weld
GENERAL NOTES:
(a) Weld beads shown above may be deposited in any sequence that will result in placement of the beads as shown.
(b) Surface temper reinforcing beads may cover the entire weld surface, or may only be placed at the toe of the weld; they may or may not be mechanically removed.
NOTES:
(1) The distance, S , is measured from the toe of the weld to the edge of the temper beads. Measurements shall be made parallel to the base metal surface.
(2) Beads near the finished surface may be both tempering beads and surface temper reinforcing beads.
This copy downloaded on 2015-07-13 07:36:37 -0
Surface Temper Weld Reinforcing Beads
Copyrighted material licensed to University of Toronto by Thomson Scientific, Inc. (www.techstreet.com).
ð15Þ
Figure QW-462.13
Measurement of Temper Bead Overlap
Direction of
bead sequence
a
b
Overlap length
GENERAL NOTE: Measurement of bead overlap – % overlap length = (a − b)/a × 100%. In this figure, the shaded bead overlaps previous
bead by 30% to 40%. The distance a is measured before the next bead is deposited.
Figure QW-463.1(b)
Plates — 3/4 in. (19 mm) and Over Thickness
and Alternate From 3/8 in. (10 mm) but Less
Than 3/4 in. (19 mm) Thickness Procedure
Qualification
Figure QW-463.1(a)
Plates — Less Than 3/4 in. (19 mm)
Thickness Procedure Qualification
This copy downloaded on 2015-07-13 07:36:37 -0500 by authorized user logan ahlstrom.
207
Copyrighted material licensed to University of Toronto by Thomson Scientific, Inc. (www.techstreet.com).
ASME BPVC.IX-2015
No fu
Figure QW-463.1(c)
Plates — Longitudinal Procedure Qualification
208
This copy downloaded on 2015-07-13 07:36:37 -0500 by authorized user logan ahlstrom.
Figure QW-463.1(d)
Procedure Qualification
Copyrighted material licensed to University of Toronto by Thomson Scientific, Inc. (www.techstreet.com).
ASME BPVC.IX-2015
No fu
Figure QW-463.1(e)
Procedure Qualification
Figure QW-463.1(f)
Notch-Toughness Test Specimen Location
This copy downloaded on 2015-07-13 07:36:37 -0500 by authorized user logan ahlstrom.
209
Copyrighted material licensed to University of Toronto by Thomson Scientific, Inc. (www.techstreet.com).
ASME BPVC.IX-2015
No fu
