Table 4-1. Maximum & Default Values for Size Definition

PI 9.xx



Chapter 4: Sizes



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition

Item



Coral Systems

Fun cti on

SL



SVC



4 GC



TRUNKS

Maxi mum Trunks



Display purposes only. Shows the maximum trunk

Defined by

Current Authorization capacity for all PRI, LGS, E&M and DID trunks. The

maximum number of trunks cannot be changed.

(SAU)



Maximum*



Defined by

Max Trunks



LG S

Default



30



Maximum*



DI D



8



Shows the current E&M trunk capacity for the

following card types:

4TEM, T1-E&M, 30T-E&M.



Defined by

Max Trunks



E&M

Default



8



30



4



Shows the current CO loop and ground start trunk

capacity for the following types of cards:

4T, 8T, T1-LS/GS, 30T-DOD, 30T-NONDID, GID,

ALS70-LS/DID/NONDID.



4



Maximum* Defined by Max Trunks Shows the current Direct Inward Dial (DID) trunk

capacity for the following card types: 8DID, 30T-DID,

Default

30

8

8

BID.

Maximum*



Defined by

Max Trunks



Shows the current Primary Rate Interface (PRI)

circuits for ISDN, or the number of B channels.

This parameter affects the maximum PRI 23/30

cards on PRI channels that can be installed (see

page 26-11).

For PRI23 enter 24.

For PRI30 enter 30.



PRI

(I SDN)

{V8. 3x}



Default



TBR

(I SDN)

{V8. 5x}



Maximum*Defined by Max Trunks Shows the current Basic Rate Interface (BRI)

Trunk circuits for ISDN, or the number of B

channels.This parameter affects the maximum

Default

32

0

0

4TBR and 8TBR cards on BRI channels that can

be installed (see page 26-11).

For 4TBR enter 8.

For 8TBR enter 16.



*



30



0



0



The maximum values in systems with MSX Common Control are set individually during Initialization by the

Authorization Unit.

The total number of LGS, E&M, DID, PRI and TBR trunks cannot exceed the Maximum Trunks value.



total number of current

 TheMax Ports value. SLT, KEYSETS and TRUNKS cannot exceed

the



4-5



Chapter 4: Sizes



PI 9.xx



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Co ral Systems

I tem



Fu nction

SL



SVC



4 GC



LI BRARIES

Maxi mum Li brari es

(Private and Publ ic)



8192



8192



8192



Maximum



4096



4096



4096



400



1000



500



4096



4096



4096



400



1000



500



PRIVATE



PUBLIC



Default

Maximum

Default



Display purposes only. Shows the

maximum number of Public and

Private libraries. The maximum

number of libraries cannot be

changed.

Shows the current capacity for

station related speed call numbers

on DBX, see note 2 below.

Shows the current capacity of the

system public libraries.



 1) The total number of Private and Public Libraries cannot

exceed 8,192.

2) Private Libraries must be defined as 10, in DX systems,

when Priv_Lib_On_Disk is utilized (see page 4-16).

3) When Large Pub Library (below) is used, it is advisable to reduce PUBLIC

(above) capacity to the minimum required.



LARGE_NPL

{V8.5x}



LARGE_PUB_

DI GIT S

{V8.5x}



Maximum



65,000



65,000



65,000



Default



0



0



0



Maximum



1000



1000



1000



Default



0



0



0



Maximum



LARG E_PUB

{V8. 5X}



51



51



51



Default



0



0



0



4-6



Shows the current capacity of the

system Large Public Libraries.

Shows the available number of

memory units for the Large Public

Numbering Plan

(see Notex on page 4-8).

Determines the maximum number of

digits available for dialing out on a

trunk via the Large_Public Lib.

The number here cannot exceed the

number defined in MAX_DGTS_ON_TK,

Route: SFE,0 (see page 6-7).



PI 9.xx



Chapter 4: Sizes



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Co ral Systems

I tem



Fu nction

SL



SVC



4 GC



G ROUPS

Maximum



BELL /UNA



Z ONE PAGE



6



6



6



Default



3



2



3



250



250



250



5



20



10



1024



1024



1024



30



100



80



Maximum

Default



BO SS



Maximum

Default

Maximum



250 up to(V8.5x)

512 from {V8.60}



PI CKUP

Default



G RP_CAL L



100



Maximum



500



500



500



10



30



30



Maximum



250



250



250



0



0



0



Shows the current capacity for Zoned

Voice Page groups.

Shows the current capacity for Boss

groups.

Shows the current capacity for

Pick-Up groups.



60



Default



HUNT



30



Shows the current capacity for

Bell/Universal Night Answering

(UNA) groups.



Default



4-7



Shows the current capacity for

UCD/ACD Hunt groups.

Shows the current capacity for

conference group calls.



Chapter 4: Sizes



PI 9.xx



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Coral Sy ste ms

Item



F unctio n

SL



SVC



4 GC



120



120



240



24



120



64



Maximum



6



6



6



Minimum



1



1



1



Default



2



2



2



Maximum



500



500



4000



Default



200



500



200



Maximum



250



250



250



4



4



4



Maximum



250



250



250



Default



16



64



16



Maximum



950



950



950



1



100



100



4

128



4

128



4

128



1



32



32



Maximum



PEM/DPEM Default



RMI /ASU

CARD



NUM_PLAN

O FFSET_

FI LTER

{V9.2x}

COS

SMDR_

BACKUP



DATA_

PORTS



Default



Default

Minimum

Maximum

Default



Shows the current capacity of the

Programmable Expansion Modules (PEMs).

The PEM size must be less than, or equal to,

the number of keysets.

Shows the current capacity for RMI/ASU

and 4/8DRCM cards.



o Shows the available number of memory

units for the system Numbering Plan.

Shows the current number of offset filters

defined.

Shows the current number of Classes Of

Service.



Authorization Limit

Shows the available number of records for

SMDR backup buffer.

Shows the current number of asynchronous

data ports available for Voice/Data Keysets

(VDK/VDM) and Terminal and Data Interface

Modules (TIMs and DIMs).

Changing this field affects the PORT and

TERMINAL fields on page 4-11.



oThe values entered into LARGE_NPL, NUM_PLAN and TOLL_BAR define the quantity of memory units available.

They do not define the number of entries. Each entry may use more than one memory unit. The relationship

between the value entered and the number of entries is defined by the following formula:

NUM_PLAN :

# of memory units used = (2 × # of From/To Dial# entries) +the # of (From Dial # = To Dial # ) entries.

From/To Dial # is used when the From Dial # is different from the To Dial #.

Where:

From Dial # = To Dial # is used when the From Dial # is equal to the To Dial #.

TOLL_BAR :

Approximate # of Toll memory units used = 4/7 × ([2 ×Digits] + [4×Entries])

Digits=

the sum of all digits entered in TOLL_BAR.

Where:

The wild card characters are counted as single digits each time they appear.

Entries = the # of elements in the Toll list.



4-8



PI 9.xx



Chapter 4: Sizes



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Coral Sy ste ms

Item



F unctio n

SL



TO LL_

BAR



4 GC



600



Maximum



SVC



600



600



500



20



20



100



2



10



10



Maximum



N/A



16



960



Default



N/A



16



4



Maximum



200



Default



DVMS_

PORT



500



Maximum



CO NF_

CKTS



Default



10



Default



PAGE_Q



Maximum



1000



Shows the available number of DVMS ports

that can be utilized (one 4VS or 4VSN card

is equipped with four DVMS ports).



10



65,000

from {V8.5x}

Default



Shows the available number of

Conference ports that can be utilized. Two

ports are required for each CNF card when

used as a CONF card. One port is required

for the CNSsl Conference Card.



1000 upto (V8.5x) Defines the maximum number of software

identification numbers (index) that can be

2000 from{V8.60} assigned to the Page Queue numbering

plan.



10,000

up to (V8.3x)



VFAC_ACCT



0



0



Maximum



128



128



128



Default



10



5



5



64



Shows the available number of Account

Codes that can be utilized in VFAC. The total

number is also dependent on #ACCT_DGTS in

[SFE].



0



Maximum



WAI T_QUE

{V9. 2x}



o Shows the available number of memory

units in the Toll Barriers programming area.



NETWORK_

OAI _

Default

SERVI CES

{V9. 2x}



20



Shows the maximum number of

destinations for calls waiting for routing

access.



N_Calls* N_Calls* Defines the maximum number of Network

and OAI Resources. CoraLINK and ISDNet

use these resources to implement such

25

25

Network features as Call Transfer and OAI

features such as MakeCall.

*N_Calls is defined in Table 4-2.



4-9



Chapter 4: Sizes



PI 9.xx



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Coral Systems

Item



Functi on

SL



SVC



4GC



Range



Y/N



Y/N



Y/N



Default



N



N



N



NET _NODES Maximum

{V9. 2x}



250



250



250



10



5



5



Maximum

NET _

FEATURES

{V9. 5x}



445



NETWO RK

{V9. 3x}



Default



Default



445



150% of the

Stations

0

ISDN



Defines whether this PABX is part of a

Private Network. If Y, then a default for

NET_NODES and NET_FEATURES is set.

Otherwise, NET_NODES and NET_FEATURES

are set to 0 by the system.

Shows the available number of Network

Nodes.

This parameter can only be defined if

NETWORK (above) is set to Yes.

Display Purposes Only.

Shows the current capacity for

simultaneously active ISDNet features.



0

{V8.3x}



NETWORK_ Maximum

FACI LIT IES Default



250



250



250



10



16



16



Maximum

NUMBER

OF

Default

ALTERNATE

ID



3200



256



256



20



64



Shows the available number of Public

Network Service Facilities (NSF). For

example: MCI, SPRINT, AT&T.



64



Shows the number of Alternate Line

Identification Numbers.



ROUTI NG (Au th orizatio n Limi t)

Maximum



ROUTI NG

ACCESSES Default

DI AL

SERVI CES



Maximum

Default



Maximum

ROUTE

EL EMENTS

Default

{V9. 2x}



{V8. 3x}



4



4



4



2



1



1



Shows the current capacity for

Routing Accesses and defines the

different numbering plans for

programming ISDN.



255



255



255



Shows the current capacity for Dial

Services.



20



30



30



250



250



250



30



50



50



4-10



Shows the current capacity for Route

Elements

(See Chapter 15).



PI 9.xx



Chapter 4: Sizes



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Coral Systems

Item



Functi on

SL



Maximum

CO ST _

EL EMENTS

Default



ROUTING_ Maximum

ELEMENTS_

Default

NPL_SI Z

{V9. 8x}

ROUT ING_ Maximum

NPL

Default

EL EMENTS

{V9. 8x}



SVC



4GC



1



50



50



1



10



10



Not Applicable*

5



5



5



Not Applicable*

800



800



800



Shows the available number of Cost

Calculation Elements (see Chapter 15).

Calculate the average size (average

amount of digits per Element) of all the

Routing Numbering Plan Elements (see

Chapter 15).

Estimate the number of Routing

Numbering Plan elements (see Chapter

15) used in the system.



DATA FEATURES (Authori zati on Li mit)

NOT APPLI CABLE fo r Co ral SL

Maximum



128



128



Default



NA



60



60



Maximum



NA



16



16



Default



NA



16



16



NA



10



10



Default



NA



10



10



Maximum



NA



128



128



Default



NA



32



32



Maximum



NA



20



20



Default



USER



NA



NA



10



10



Maximum



NA



128



128



Default



NA



100



100



COS

PO RT_TYPE Maximum



CAL LS



GRO UP



G ROUP_

MEM



*



Shows the maximum number of users that

are allowed to use or contact the data switch.

Users are defined as a specific piece of data

processing equipment or an individual.

Shows the current number of data COSs

available in the system. Data COSs are

used to enforce connectivity restrictions.

Shows the maximum number of different

port types that can have a different set of

profiles associated with it.

Defines the maximum number of

simultaneous data conversations (sessions)

that can take place on the Coral.

Defines the current number of data groups

that the data users may be organized into.

Defines the maximum number of data

users that can belong to any one data

group.



Both parameters are defined by and limited by the following equation:

ROUTING_ACCESSES x [ROUTING_NPL_ELEMENTS x ((ROUTING_ELEMENTS_NPL_SIZ x 2) + 5)] <32,000



4-11



Chapter 4: Sizes



PI 9.xx



Sizes Def - Route: SIZ (or 0,0,0,1)

Table 4-1. Maximum & Default Values for Size Definition (cont.)

Coral Systems

Item



Functi on

SL



4GC



Maximum



NA



128



128



Default



PORT



SVC



NA



32



32



Display purposes only. Defines the

maximum number of physical data ports

that can exist at any given time. A data

port is either a VDK or TIM or DIM. To

change the default for this parameter, use

the DATA_PORTS field on page 4-8.



CHECK MEMORY (Y/N)?

Instructs the system to display the database memory status. When the System Size

table is displayed without modification, CHECK MEMORY displays how much memory

remains in the system database as follows:

XXXXX BYTES USED BY RAM.

XXXXX BYTES LEFT IN MEMORY.

When changes are made to the System Size table, CHECK MEMORY displays the system

memory status as if changes made to the current sizes were updated as follows:

MEMORY EXCEEDED BY XXXXX BYTES, CAN’T UPDATE.

•



This message indicates that the memory tables have been exceeded. The

technician should try to reduce the values of less important table parameters

thus freeing memory for the recent updates. If this is not possible, additional

DBX memory cards should be purchased.



XXXXX BYTES USED BY DATABASE, AUTO BACKUP AVAILABLE.

XXXXX BYTES USED BY DATABASE, AUTO BACKUP NOT AVAILABLE.

•



Range:



When the system database memory is exceeded, the technician should try to

reconfigure the table values assigning smaller values for less significant

parameters. The technician can also try to perform a manual backup

depending on the database size as described in Chapter 21.

Yes/No;



Default:No



UPDATE (Y/N) ? (*warning*:Upon update, database is lost)

Loads the modified SIZE information, initializes the database and resets the system.

When No is entered, all previous entries are ignored and the system remains at the

previously programmed sizes.

Range:



Yes/No;



Default: N/A (Yes or No must be entered)



4-12



PI 9.xx



Chapter 4: Sizes



Sizes Tab - Route: SYSGEN,2 (or 0,0,0,2)

CURRENT_Config (Default/Modified)

Shows whether or not a change was made in SIZE. If a change was made, the word

“MODIFIED” is shown. If no change was made, then the word “DEFAULT” appears.

Range: Default/Modified



Table 4-2. Maximum & Default Values for Size Table

Coral Systems

I tem



F unctio n

SL

Maximum

Default



SVC



4GC



250



64



250



40



64



32



512



64



512



64



64



256



400



400



400



80



400



150



RESOURCES



Maximum



N_CAL LS

Default

Maximum



CAL LS_Q

Default

Range



ACD_

Default

STATI STICAL

_

SEARCH

(Y/N)?



Maximum



PARTY_

Default

NUM/ NAME

{V9.2x}



Defines the number of ports needed for

all the Shared Service cards together in

the system.

Card Type

# Ports Needed/Card

4DTR, 4RMsl

4

8DTD, 8DTR, CNF(C3Way), 4DRMsl 8

4RCMsl

10

4DRCMsl

14

16 MFR (MFC)

16

Defines the maximum number of calls

that can be simultaneously made within

the system.

Defines the number of calls that can be

simultaneously placed on Hold, Page_Q,

Park or Multi-Appearance.



Yes/No Yes/No Yes/No In order to enable the statistical search

No



500

60



No



No



feature in ACD Hunt groups, this option

must be set to Yes.

The statistical search procedure requires

an idle time counter for every group

member. This option, when set to Y,

allows you to define ACD groups with

statistical search type (see Hunt Group,

Chapter 10).



Defines the maximum number of records

used for saving the Calling Party Number

1⁄2(Max. Trunks - and Name and the Connected Party

ISDN Trunks) + Number and Name. Each record can be

accessed at any time during the call.

ISDN trunks

The Calling Party Number is displayed on

the SMDR.



500



500



4-13



Chapter 4: Sizes



PI 9.xx



Sizes Tab - Route: SYSGEN,2 (or 0,0,0,2)

Table 4-2. Maximum & Default Values for Size Table

Coral Systems

I tem



F unctio n

SL

250



250



250



20



15



15



500



500



500



20



50



25



N/A



N/A



Y/N



Default



NETWORK

SERVICES

{V9.2x}



4GC



Maximum



ISDN_

TRANSIT_

SET UPS

{V9.2x}



SVC



N/A



N/A



N



Maximum

Default



Maximum

Default



DISPATCH_

I N_SYSTEM

{V9.5x}



NO_OF_CALL Maximum

_TRACE_

Default

RECORDS

{V9.7x}



Defines the maximum number of ISDN

call setup information to be stored

simultaneously.

ISDN call information is used for

completing the call setup.

Defines the maximum number of Network

Supplementary Feature procedures that

can be performed simultaneously.

Network Call Transfer is one example of a

NSF procedure.



Used only in 4GC systems.

Defines whether simultaneous trunk

“dispatches” (one-way transmissions to

other trunks) can be defined and used by

the external system CTI applications used

for GeoTech cellular phones.

Entering Y allows a maximum of 128

simultaneous trunk dispatches (including up

to 32 trunk members per dispatch).

Entering N cancels the feature.



32,000 32,000 32,000 Defines the maximum number of

0



100



100



4-14



incoming calls that may be recorded and

listed (“traced”) for the entire system.